Click here to buy!

Makita 10″ Dual Slide Compound Miter Saw with LASER with full Makita warranty !!!! LS1013L This tool is FACTORY RECONDITIONED With a 1 year Makita warranty Model #: LS1016L Makita Suggested List Price: $529.00 AN AWESOME TOOL AT AN UNBELIEVABLE PRICE! Special Offer! Sale goes while supplies last! – Limited Quantity! Largest crown molding cutting capacity in its class Compact design with a patented 4-Steel Rail Sliding System further increases rigidity to produce superior cuts Exclusive 6 linear ball bearings deliver smooth, solid, and adjustment-free “dead-on” accurate cuts Increased capacity for up to 6-5/8″ crown molding (vertically nested), 4-3/4″ baseboard (vertical), and 12″ cross cuts at 90º Innovative direct drive gearbox and guard system is engineered for increased vertical cutting capacity Miters 0º-52º left and 0º-60º right, with positive stops at 0º, 15º, 22.5º, 31.6º, and 45º (left and right) Less weight (52.2 lbs.) and the most compact design in its class for easy jobsite portability Powerful 15 AMP direct drive motor requires less maintenance, and delivers 3,200 RPMs with soft start for smoother start-ups Electronic Speed Control maintains constant speed under load for smoother, higher quality cutting Exclusive 4-3/4″ tall dual sliding fence system features upper and lower fence adjustments for more precise miter and bevel cuts Built-in laser clearly indicates line of cut with micro fine adjustments; independent switch allows laser to be seen with and without the blade rotating Dual rear-handle bevel lock is easily accessible and adjusts 0º-45º (left and right), with positive stops at 22.5º, 33.9º and 45º (left and right) Ergonomic rubberized horizontal D-handle design for better fit and added comfort Easy one-touch miter lock for accurate adjustments and increased efficiency Replaceable stainless steel miter scale features large and easy-to-read markings Large precision-machined aluminum base supports material for more efficient cutting Easy to read dual bevel scale for more precise adjustments See-through blade guard system for greater visibility of blade and line of cut Easy one-step blade changes for increased efficiency Rubberized feet help tool stationary Large adjustable fence levers for fast and easy adjustments Oversized trigger switch for better fit, added comfort and easier operation Fully enclosed bottom throat plate for a cleaner work surface 4-1/2″ base height enables user to use three (3) 2x material for temporary table extensions INCLUDES: 10″x 5/8″ 60T TCT Saw Blade (A-93675) Vertical Vise (122854-6) Dust Bag (122852-0) Triangular Rule (762001-3) Socket Wrench #13 (782232-8) Hex Wrench (783208-8) Blade Diameter 10″ Arbor 5/8″ Crown Moulding (nested) 6-5/8″ Baseboard (vertical) 4-3/4″ Max. Cutting Capacity Miter Capacity 90° 4-3/4″ x 12″ 45°L/R 2-1/2″ x 8-1/2″ No Load RPM 3,200 AMPS 15.0 Size(L x W x H) 28-1/8″ x 25-1/4″ x 26-1/2″ Net Weight (lbs.) 52.2 Shipping Weight (lbs.) 64.0 UPC Code LS1016L 088381-099585 FACTORY RECONDITIONED Shipping information NO P.O BOXES,APO,OR FPO(HI & AK & canada & (prefer not required)).* PAYMENT TERMS Payment must be received within 7 days Credit Cards Accepted PAYPAL ” . Email me with any questions. THANKS FOR BIDDING!! Feedback POLICY Our feedback is automated once we are paid and receive pos feedback our selling manager program automatically gives you a glowing review it updates hourly Once again thanks for shopping with us!! Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.

Technorati Tags: makita miter saw, miter saw

Click here to buy!

wwwliondaptercom Store MAKITA 18V NI-CD 1.3 Ah PA18 2.0 Ah 1822 CHARGER DC1804 BATTERY ADAPTER CONVERT 18V MAKITA NI-CD & NI-MH TOOLS TO LITHIUM-ION BATTERYA SPECIAL ADAPTER IS USED FOR THE MITER SAW – PLEASE SEE OTHER AUCTIONS FOR ORDERING A New Idea in the Form of an Adaptor to Convert your 18V Makita Ni-Cd & Ni-Mh Powered Tools to Run on the new Lithium-Ion Batteries ( models BL1815 & BL1830) If your looking to replace your old Ni-Cd batteries and have heard about the benefits of Lith-Ion technology then this is for you. A cheaper alternative to a new set of tools. Simply attach one end of the adaptor to a Lith-Ion battery and the other end to your tool Will work on all 18V Makita except for the cordless miter saw which we also have an adapter for, please see other ads if you need one specifically for the miter saw. Do not attempt to try and charge Lith-Ion batteries in an old “pod style ” charger as they will cause immediate damage to both the charger and battery. PAYMENT: We accept the following forms of payment only: Paypal WARRANTY: 30 Day Full Warranty TERMS AND CONDITIONS: · Bidders and buyers have to read and agree to terms and conditions before bidding or buying. · The winning bidder must complete the sale transaction (including checkout and payment) within 7 (seven) days of the end of sale. Otherwise, you will be considered as a NON-PAYING buyer. Ebay will be notified and item will be relisted. · Seller is not directly liable for any loss, theft or damage to goods while in transit. It is strongly recommended buyer to take up insurance option. · If problems do arise, please contact us before leaving any feedback, and we shall endeavour to resolve any issues. · Whilst all care is taken, any errors or omissions in the product information/description are unintentional. LIONDAPTER IS A TOOL MODIFIER, ADAPTING THE OLDER 18 VOLT MAKITA “POD STYLE” NICKEL CADMIUM AND NICKEL METAL HYDRIDE CORDLESS TOOLS TO THE NEW LITHIUM ION SLIDE BATTERY. LIONDAPTER MODEL #18V. LITHIUM ION IS LIGHTER, HOLDS A SHELF CHARGE LONGER, CHARGES FASTER AND HAS NO MEMORY EFFECT. USE THE FULL SIZE OR HALF SIZE BATTERIES. TOOLS AND BATTERY NOT INCLUDED IN AUCTION. DANGER – NEVER PLACE LIONDAPTER IN THE OLDER “POD STYLE” CHARGERS. LITHIUM ION WILL NOT CHARGE PROPERLY IN THE OLDER CHARGERS. THE LIONDAPTER IS COMPLETELY GUARANTEED FOR 30 DAYS. SIMPLY RETURN THE ADAPTER FOR A FULL REFUND. PAYPAL ACCEPTED. INTERNATIONAL MAIL COURIERS IN YOUR COUNTRY MAY CHARGE ADDITIONAL VAT OR OTHER FEES. Green Liondapter Recycle Tool NiCad NIMH -ION Impact

Technorati Tags: makita miter saw, miter saw

Click here to buy!

I only accept Paypal. This No Reserve auction is for a set of 5 thoroughly used, 12″, compound miter saws. They are all in cosmetically rough shape but they do work. I have replaced most of the needed parts like arbor bolts, locking pins, knobs, plugs, kerf plates and dust chutes as needed on some of the saws. There are 3 DeWalt DW705 saws, a Makita LS1220 and a Makita LS1221. One of the Makita saws is missing part of the fence, but the “important” part is there and it will cut and support your work just fine. There are no blades, wrenches or dust bags included. I will throw in a brand new DeWalt 80-tooth blade for $50 per saw. This item listed as pick-up only, but I may be willing to facilitate shipping at the buyer’s considerable expense. Please e-mail if you have any questions. Check my feedback and bid with confidence. I only accept Paypal.

Technorati Tags: makita miter saw, miter saw

Click here to buy!

Toll Free: 1-877-987-2819 Jean-Claude Cayer Enterprises LTD. Pneumatic & Electric Tools – Outdoor Power EquipmentSmall Engines – Nails, Staples, Screws – Compressors Petits moteurs – Clous, agrafes, vis – Compresseurs Outils pneumatiques et électriques – Équipement de pelouse et jardin Shop by Category -Cordless Tools -Corded Tools -Framing Tools -Accessories -All -Air Guns -Miter Saws and Accessories -Hand Tools -Makita Lithium-Ion Tools -Air Compressors -Table Saws and Accessories -Other Bosch CRS180B 18V Cordless Lithium-Ion 1-1/8-in Reciprocating Saw (Tool Only) Condition: New MSRP*¹: $349.00 Photo Bosch Warranty. Features: Compact size makes it easier to get into tight spaces Lightweight tool equals less fatigue 2-speed allows you to adjust to the material your up against Lock-Jaw blade holder is the easiest blade change system 1-1/8-in stroke allows for more material to be removed per stroke Variable speed trigger helps you ease into the material without a kickback Specifications: Voltage18V SPM0 – 2,400 / 0 – 2,700 Stroke Length1-1/8-in Orbital Action:No Keyless Blade Clamp:Yes Variable Speed Trigger:Yes Battery Type:Li-Ion Battery Amp Hours:2Ah Length17.4-in Weight7.6 lbs. No. of Batteries Included:Tool Only Includes: 18V Cordless Lithium-Ion 1-1/8″ Reciprocating Saw (Tool Only) – CRS180B Closer View/More Photos PLEASE NOTE INTERNATIONAL BUYERS, YOUR COUNTRY MIGHT CHARGE YOU DUTIES AND TAXES, THIS IS COMPLETELY OUT OF OUR CONTROL AND INCALCULABLE Jean Claude Cayer Enterprises LTD. Policies About Us We would like to take this opportunity to introduce ourselves. We are the leading and professional supplier of Electric and Pneumatic tools in the eastern Ontario region. We operate in the following channels: Industrial – Wholesale (Dealers) – Retail – Lumber Yards and Rental Outlets. We have been in business for 18 years. Yes we can write and speak in English and French fluently Payment Methods Information We only accept PayPal as a method of payment for purchases made on eBay. Contact Information Mailing Address: Jean-Claude Cayer Enterprises LTD. 708 Limoges Road Limoges, Ontario K0A 2M0 Canada Telephone: 1-613-443-2293 Toll Free Telephone: 1-877-987-2819 Fax: 1-613-443-2022 Business Hours: FROM MONDAY TO FRIDAY 7:00 AM to 5:00 PM(17:00) Eastern Standard Time Item’s Condition All our items are BRAND NEW unless declared otherwise. Normally if it is Reconditioned/Refurbished/Used it will be clearly writen in the title and/or in the description. Authorized Dealer and Service We are authorized Delaer and Service Center of all the brands we sell on eBay. We can cover all the warranties ourselves. BUY WITH CONFIDENCE Stock We normaly have everything we sell in Stock, we may sometimes run out stock due to selling here in the local store, at that time we order more of the item(s) in question and we will either offer a full refund or having a small waiting period! Sales Tax We must charge Federal and Provincial taxes. Ontario, New Brunswick and Newfoundland and Labrador Residents must pay 13% HST Quebec Residents must pay 5% GST and 8.5% YVQ/PST over the 5% GST. British Columbia Residents must pay 12% HST Manitoba, Prince Edward Island, Saskatchewan, Alberta, Northwest Territories, Yukon, Nunavut Residents must pay 5% GST. Shipping Information Shipping cost can be calculated by going to the “Shipping and payment” tab. Shipping Method Used All our item(s)/shipment(s)/package(s) are sent VIA UPS. Domestic(Canadian) shipments are shipped via UPS Standard(ground) unless asked otherwise by customer(extra charge), United States shipments are shipped vis UPS Standard(ground) unless asked otherwise by customer(extra charge), International(excluding United States) shipments are shipped via UPS Express Saver(air) unless asked otherwise by customer(extra charge). Delivery Waiting Time Canadian shipments should take between 1-7 Business days depending on your location in Canada. United States shipments should take between 3-8 business days depending on your location in United States and if it doesn’t get held in customs. International shipments should take between 2-8 business days depending on your location in the world and if it doesn’t get held in customs. BUY & PAY BEFORE 3:00PM EASTERN STANDARD TIME and we ship the same DAY! please note there is exceptions Tracking Number will be emailed and attached to your paypal payment Jean-Claude Cayer Enterprises is not responsible for any customs fees charged by your country, please contact us for more information. Thank you for understanding Local Pick-up and Prices We do not accept local pick-up. We do have the same prices in our local store has on eBay. eBay transactions/purchases can only be shipped. If you want to pick-up your item please contact us(see Contact Information tab). All prices are the same from eBay, our website and our local store, feel free to drop by and shop in the store with our experts sales representatives. Returns and Services If your are not satisfied with your purchase, you can return it at your cost for a refund. Refund is the total for the Product, original shipping will not be refunded. Taxes(if applied) and Total of the product will be refunded. We are authorized Service Center of all brands we sell on eBay and on our website, we will gladdly repair any tools that has been broken, free of charge if still under warranty, or with $60.00 CAD labour + parts if warranty as expired. For the lenght of the warranty from the manufacturer please refer to the “Manufacturer’s Warranty” tab just bellow the main picture/photo.. *¹ = Manufacturer’s suggested retail price Copyright © 2008-2012, JCCayer – 708 Limoges Road, P.O Box 280, Limoges, Ontario, K0A 2M0, Canada

Technorati Tags: makita miter saw, miter saw

Click here to buy!

721471-A 12″ 50-tooth Carbide-Tipped Miter Saw Blade Ultra-thin design lightens cutting load Alternate Top Bevel tooth configuration all 4 tooth surfaces are precision ground for accurate cuts for wood 1″ arbor specifically desinged for clean accurate cutting with Makita slide compound miter saws special blade tensioning prevents vibration increases, which can be a problem with many thin kerf blades multi-stage heat treatment eliminates bending tendency of blade. Particularly important when cutting both left and right hand miters New top quality professional miter blades designed specifically for performance under the extra heavy loads imposed on saw blades by miter cuts. Both the length of the cut and number of teeth in the cut at one time are greater than with a straight cut. This increases the load on the blade. Lower quality blades have difficulty cutting a straight line under these conditions and will often try to follow the grain of the wood, which is the easiest path, resulting in irregular cuts. Diameter Arbor No.Teeth Grind Hook Angle Thickness Kerf Max. RPM Part # Model 12″ 1″ 50 ATB 8º .071″ .091″ 5,000 721471-A LS1212, LS1221 Your browser does not support JavaScript. To view this page, enable JavaScript if it is disabled or upgrade your browser. Click Here. Double your traffic. Get Vendio Gallery – Now FREE! Your browser does not support JavaScript. To view this page, enable JavaScript if it is disabled or upgrade your browser.

Technorati Tags: makita miter saw, miter saw

Click here to buy!

This Incra TSCOMBO #4 52″ Range TSLS Super System with 28″ x 32″ Right Side Router Table is Brand New! Incra TSCOMBO #1 Contains: 1X 32” Range INCRA LS32 Positioner 1X Pair of 92” TS Rails 1X Base Mount Unit for LS32 1X TS-IIIA Rip Fence 1X INCRA Wonder Fence 1X INCRA JUMBO Right Angle Fixture 1X 28” x 32” TS Router Table for RIGHT side 1X Master Reference Guide 1X 51-Piece Template Library 1X All Instruction Manuals 1X 82-Minute Instructional DVD 1X Solid Aluminum MagnaLOCK Plate 1X INCRA Shop Stop 3X MagnaLOCK Ring Inserts (1”, 2 1/8”, 3 5/8”) 1X TS Router Table Mounting & Support Kit Incra TS-LS32 Features & Specifications: The NEW INCRA TS-LS offers the one thing that every table saw fence should have, but none of them do, namely, Automatic Positioning Control. All other table saws depend on a tape measure and your eyesight to position your work. That’s why all table saw users are resigned to the fact that a good cut requires long set-up times and endless trial and error. The INCRA TS-LS completely eliminates the need for these tedious processes by using INCRA’S patented lead screw technology to position your work instantly and automatically to within 0.002″. Even better, if you want to repeat a cut, you can return to any former position in less than 5 seconds with ZERO repeatability error. This kind of accuracy and perfect repeatability are luxuries that woodworkers could only dream about before the INCRA TS-LS. And because of its structural design, centrally placed carriage, and optimized side mounted clamping system, the entire unit virtually welds itself together into one solid block of steel and aluminum when locked in place. The result is exceptional strength, rigidity and stability. Five Sliding Scale Template Channels Two of the channels are used for primary (distance from the cutter) and floating (distance from the last cut) reference scales. The 32″ stainless steel scale fits in another channel leaving two more for your choosing. These scales combined with Incra’s patented positioning racks allow you to return to any former position in less than 5 seconds with ZERO repeatability error. After setup, you also get perfect measured cuts just as fast. Easy On, Easy Off Dismounts for cross-cutting operations and remounts in less than 10 seconds. This also makes it easy to use INCRA precision on both sides of the blade. The positioning range is 32″ to the right and 16″ to the left of the blade. Saddle brackets not only allow fast dismounts, the clever design of INCRA’s centrally placed carriage literally forces the fence into perfectly parallel alignment at any position. The saddle brackets also rise above the table saw surface to allow movement almost anywhere along the 72″ rails in either direction. The fence skims above the table on whisper smooth glides, eliminating all fence to table contact. Quick, Easy Installation Universal mounting brackets virtually guarantee compatibility with any 10″ table saw, with no drilling, no tapping and no modifications. Positioning range – right of blade: Over 32″ Positioning range – left of blade: Over 16″ Positioning accuracy: .002″ over full range Repeatability: Return to any former position in less than 5 seconds with ZERO repeatability error Fence length: 36″ Incra’s Patented Steel Lead Screw with Quick Action Cam Clamp and Micro Adjust Wheel with Rotating Bezel Heavy duty 72″ rail system Mounting brackets 36″ Heavy duty rip fence with T-slots on front and top Engraved 32″ Stainless Steel Magnetic Scale Incra LS Positioner 32″ Range Carriage and Tubular Base INCRA’S Patented Steel Lead Screw with Micro Adjust Wheel with Rotating Bezel and Quick Action Cam Clamp Incremental Positioning in 1/32″ Steps Continuous Micro-Positioning with Audible Dentent Every 1/1000″ Solid Steel and Aircraft Grade Aluminum Construction Throughout Hairline Cursor and “Big View” Optical Window Hardware packs and fully illustrated easy instruction manuals Incra Wonderfence Features & Specifications: The Wonder Fence ~ by INCRA is a heavy-duty, one-fence solution designed for all your routing operations, shaping, edge-forming and precision joinery. When your work demands the utmost in accuracy, INCRA has gone the extra mile with this tool. The split fence halves and base fence are machined flat to insure a perfect woodworking surface. You won’t find a warp, bend or bow in these INCRA fences. The offset adjustment wedges have literally been machined from solid blocks of aluminum to insure precise offset adjustability. Setting up for split-fence operations has never been easier or more accurate. Innovative Features of the Wonder Fence: • Heavy-duty precision machined aluminum split fence,wedges and base fence • Infeed and outfeed fences are independently adjustable in 2/1000″ steps over 1/8″ range • Laser engraved offset scale • Each offset mechanism has it’s own cursor and scale marked off in 2/1000″ increments • Lock-down offset permits gap adjustment • Adjustable fence gap width to 4 1/2″ • Hi-Rise™ Raised Panel Cap for vertical panel raising • Built-in dust collection port with attachment elbow fits industry standard hoses • All aluminum construction and fully assembled Incra Shop Stop Features & Specifications: Included in the Wonder Fence – Includes machined flat split in-feed and out-feed fences, highrise fence cap, base fence, dust collection port, offset wedges, and table mounting clamps. (Base fence replaces the fence on TS-I, II, or III systems) INCRA Shop Stop – The Versatile Stop Positioner The heart of the INCRA incremental track system is the highly versatile INCRA Shop Stop. Patented Automatic Positioning Control and micro adjustability mean instant, repeatable accuracy without measuring or trial and error setups. It’s incremental, expandable, reversible, horizontally adjustable, vertically adjustable, and micro adjustable. WOW! If you have a work positioning need in your shop, you can be sure that the INCRA Shop Stop will handle it. • Expands to accommodate any fence thickness up to 1-1/2″ • Vertically adjustable to accommodate any fence height up to 3-1/2″ • Micro adjustable for 1/1000″ precision • Instantly set (or reset) to any position with machine shop • Accuracy and ZERO repeatability error Shop Stop – Expanded Mode: The two-piece body expands to accommodate a wooden subfence. The INCRA Shop Stop is fully reversible and works on both sides of the cutter. Shop Stop – Standard Mode: Attaches directly to the INCRA Track or any INCRA Fence – past, present, or future. The heart of the system is the highly versatile INCRA Shop Stop. Patented Automatic Positioning Control and micro adjustability mean instant, repeatable accuracy without measuring or trial and error setups. Table Saw Router Table Features & Specifications: Incra’s new lineup of heavy-duty router table tops also includes 2 models designed specifically for the table saw. The 28″ x 32″ Right hand table serves double duty as a table board and includes a full size 3/8″ x 3/4″ T-Slot miter channel. The 28″ x 21″ Left hand table permits maximum fence system range and offers open access from the end of the table saw. These tops are designed to support even the heaviest of production routers and lifts, and will work with any standard 9-1/4″ x 11-3/4″ mounting plate. All Incra Router Tables are shipped with a 3/8″ solid aluminum router mounting plate, pre-drilled for your router, featuring the exclusive Magna-Lock magnetic throat plate system. Changing any of the included throat plates is a snap with the Magna Lock System. Just drop in the selected plate. The high energy, rare-earth magnets hold the plate secure and perfectly flush every time. All of our mounting plates include 3 laser cut throat plates with a 1″, 2-1/8″ and 3-5/8″ opening. Rather than the typical router plate leveling set screws that dig into the table’s recess requiring constant re-adjustment, Incra’s plate leveling system puts flat head levelers in the table, not in the router mounting plate. Access to these levelers is through the 10 access holes located around the perimeter of the mounting plate. Just insert the hex key in the access holes and turn to adjust. After leveling, a simple quarter turn of the corner mounted Cam-Lock securely holds the plate in the router table’s recess. All table saw based router tables include the TS Router Table Support Kit with 4 brackets and 2 table stiffeners. The brackets can be positioned anywhere along the TS System’s rail length and are vertically adjustable. The support kit is also available separately to support user made tables. The optional TS Leg set is a good choice for providing extra support at your table saw. Just slide the mounting brackets into the Incra Table Saw Fence System’s T-slotted rails. The legs are horizontally adjustable to fit any table saw depth. MagnaLOCK Plate Features & Specifications: INCRA’s 3/8″ solid aluminum mounting plates are the new standard for achieving perfect cutting results at your router table. Precision-machined aircraft grade aluminum and bullet proof hard anodized plating translate to easy glide for your workpiece. While the 3/8″ thickness is robust enough for the heaviest of routers on the market today. Designed for and included with every INCRA Router table top, these plates will fit the standard 9-1/4″ x 11-3/4″ recess in most other router table tops as well. Ten fine thread plate-leveling screws provide extreme control in leveling the plate to your table and rock solid support at any position around the plate. A simple quarter turn of the corner mounted Cam-Lock fastener securely locks the plate in the router table’s recess. All of INCRA’s aluminum mounting plates feature the exclusive MagnaLOCK magnetic throat plate system. Changing any of the included throat plates is a snap with the Magna Lock System. Just drop in the selected plate. The high energy, rare-earth magnets hold the plate secure and perfectly flush every time. MagnaLOCK’S instant, tool-free ring changes and perfectly flush fit for the rings make it simply the most convenient and best-performing ring system available. All of our mounting plates include three laser-cut steel rings with 1″, 2-1/8″ and 3-5/8″ openings, and many more ring sizes are available as accessories. • 3/8″ thick precision-machined aluminum construction. • Cam-Lock ¼ turn plate locking • Magna Lock Throat plate System. • 10 leveling screw positions. • Starter pin includedfor free-hand work. Note: Specify your pre-drilled router plate preference when placing your order. Model# Fits Routers MLP1613-AL – Bosch 1613 MLP1619-AL – Bosch 1619 MLP3612C-AL – Makita 3612C MLP621625-AL – Bosch 1611EVS, DeWalt 621, 625, Fein RT1800 MLP690890-AL – PC 690, 890, 7529, Makita 1101, Bosch 1617, 1618 Milwaukee 5616, Dewalt 618 MLP7518-AL – PC 7518, 7539, Triton TRC-001, M0F-001KC MLPFT2000-AL – Freud FT-2000 MLPM12V-AL – Hitachi M12V MLPUNDRILLED-AL – Undrilled If you do not specify the pre-drilled plate you would like we will include the undrilled plate with the order. TS COMBO Frequently Asked Questions: Q: Will it fit my saw? A: Probably. If your saw is less than 28-1/2″ deep (measured along the miter slot) and has flat surfaces at the front and rear that are square to the top, you should be in good shape. The adjustable hardware will use the existing holes in the saw in 95% of installations. Extension wings and side tables are not required, as the rails mount only to the central part of the saw’s top. If your saw is more than 28-1/2″ deep, TS-LS systems are available with a longer fence and base support panel to handle saws up to 35″ deep. Smaller saws such as bench-top and jobsite saws may need drilling and will generally need support legs under the rails. The TS Rail System is not compatible with Ryobi saws or the Jet Super Saw when it’s equipped with Jet’s sliding table accessory. See the TS Compatibility Table for more information. Note: INCRA TS Router Tables are designed to work with saws 27″-28″ deep. Q: How easy is it to install? A: It’s very straightforward, typically two hours of turning wrenches. Everything is adjustable, and the rails are self-leveling and self-aligning. Combinations including TS router tables and routing accessories include a huge amount of INCRA equipment, so setting up the entire saw/router system normally takes an afternoon. Q: How big is it? A: The rails on the TS-LS 32″ are 72″ long, and the overall width is 102″ when positioner’s carriage is extended for maximum rip. The right-hand ends of the rails are typically set 45″ from the blade. The TS-LS 52″ has 92″ rails, and the overall width is 122″ when set for maximum rip. The right-hand ends of the rails are typically set 65″ from the blade. Q: When are support legs necessary? A: Legs are not necessary when installing the TS-LS 32″ on floor-standing contractor’s saws or cabinet saws. Support legs are also not needed when installing our left-side TS router table. Legs are required when mounting a substantial extension or a TS router table to the right of the saw on all but the heaviest cabinet saws, and some support is required whenever the 92″ rails are installed or the 72″ rails positioned further to the right than on a typical installation. Q: Does it require side tables? A: No. The TS rail system attaches only to the central part of the saw’s top, and the rails will serve as the anchor point for any other accessories such as support legs, TS router tables, etc. Because the rip fence performs perfectly with wide open spaces on either side of the saw, you have flexibility in deciding how to lay out the system…you might keep your saw’s metal wings, replace a wing with a router table, reuse an existing wooden extension table, or build an extension table from scratch. Q: Is it better to have the router table at the saw or a separate router table? A: Because the table saw and router table are the two most frequently used stations in most shops, there’s no question that having a separate router table is more convenient and efficient. The drawback is the cost of separate Incra systems and slightly more shop space. If your budget or shop space are limited, installing a router table at the saw is a reasonable means of getting the same accuracy for both operations. Q: Is the left router table or right router table better? A: It’s partly personal preference and will partly depend on the saw. The router tables generally replace the saw’s metal extension wing on the appropriate side, and cabinet saws and hybrid-style saws will often have a motor housing that would interfere with the router’s motor either on the left or the right. Visit the TS System Planner and TS Compatibility Table for details. The right-side table helps fill in that area of the saw and doesn’t require moving the base assembly for routing, but it also limits routing capacity, limits access around the router, and forces you to lower the router bit to get back to sawing operations. The right-side router table also requires legs, which is a consideration if you move your saw frequently. The left side table allows full capacity, much better access around the router, and doesn’t require the use of legs. It does require sliding the TS base assembly down the rails (there are stops for repeatability), and there is less work space in front of the fence – roughly the same amount as on most center-mount stand-alone router tables. Q: What’s the size of the plate opening in the Incra router tables? A: It’s 9-1/4″ x 11-3/4″ in outside dimensions, with a 13/32″ (0.406″) depth to the flathead leveling screws. There is no industry standard opening, but this rough size is the most commonly used. Q: Is there a difference between the routing accessories in the TS Combos and the stand-alone LS router systems? A: The routing accessories are the duplicated exactly, and the systems share the same broad range of routing applications. Q: Are there any limitations in routing with a TS joinery systems compared to a stand-alone system? A: Not really. A stand-alone router system does allow access to the table saw while a routing operation is set up. Additionally, the Wonder Fence is used for every routing job on the TS Systems, while on the LS router systems, one has the option of sliding the Wonder Fence off of the standard joinery fence to eliminate the weight and bulk when doing box joints and dovetails. Shipping Costs Shown Are For The 48 States Only! AK & HI Please email for quote! Powered by eBay Turbo ListerThe free listing tool. List your items fast and easy and manage your active items.

Technorati Tags: makita miter saw, miter saw

Click here to buy!

Search Search by Category ?Air Tools Compressors ?Automotive ?Cordless ?Drywall Lifts ?Generators ?Hand Tools ?Inside The Home ?Masonry ?Outdoor Heating ?Outdoor Power Equip. ?Pool Equipment ?Power Tools ?Safety Gear ?Tarps ?Welding ?Woodworking ?Other Makita A-93675 Micro-Polished 10″ 60T Miter Saw Blade Click an Image to Enlarge Product Details Model: *A-93675* Condition: New Factory Sealed MSRP: *$62.99* Warranty: *1 Year** Features ATAF (Alternate Top and Alternate Face) tooth design for ultra precision cutting. Japanese Ultra Thin Kerf Carbide-tipped design provides smoother cuts with less drag on the motor and minimal material loss. Fully hardened and expertly hand-tensioned steel saw plates for true cuts. Micro-grain Carbide Teeth are honed with up to 600 grit for a mirror finish. Specifications Type Premium Ultra-Fine Crosscutting Teeth 100 Diameter 12″ Arbor 1″ Hook Angle 5° Kerf .091″ Plate .071″ Max Speed5000 RPM Use with Makita Miter Saw Model(s)LS1214F/FL, LS1221 Warranty 1 Year Factory Warranty 30 Day Satisfaction Guarantee Domestic International Domestic (Lower 48 States): $0.00 Canada: $35.00 2nd Day Air: $20.00 Australia: $45.00 Hawaii & Alaska: $20.00 Western Europe:** $40.00 Local Pick Up Available:* $0.00 Other International Destinations: $45.00 Orders are usually processed and shipped within 24 to 48 hours of receipt of your payment. Most orders are shipped by FedEx Ground, so please provide us with a physical shipping address (failing to do so may delay your order). We may ship an order by a different courier at our discretion (usually larger items require shipping by freight services, orders to military addresses must be shipped by USPS, etc.) Average time of arrival is 5-7 days for domestic shipments by FedEx Ground, 7-10 days for domestic shipments by freight truck, and 6-10 business days for international shipments. If you need to receive an order within a guaranteed timeframe, please contact us for rush options and expedited shipping. International Buyers – Please Note: If shipping for your country is not listed, call +1909.568.2800 for details. Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. Furthermore, we will not mark merchandise values below value or mark items as “Gifts”. NOTE: All electrical items sold by Max Tool are made for 120V use, unless otherwise specified *Local Pick Up is available at our La Verne location, Monday through Friday 9:00 a.m. to 5:00 p.m. Some items ship directly from the manufacturer’s warehouse and require further processing. Please call ahead to ensure that your item is in stock at our location before pick-up. **Western Europe Shipping is defined by the shipping destinations available in our Shipping Policies Page. For all other shipping destinations please inquire regarding the correct shipping costs. We want nothing more for our buyers than to be 100% happy with their purchase. We strive to earn a 5-star rating from every purchase. When you receive your purchase, please take a moment to leave us a positive feedback. If there was something unsatisfactory about your purchase, please contact us through eBay or call us at 800 629 3325 before leaving feedback and we’ll do what’s necessary to remedy the problem and ensure your satisfaction! When your order ships from our warehouse, we will automatically leave you a positive feedback PayPal Accepted, Immediate Payment Only. Your order will usually ship within 24-48 hours after payment has been received. For more information on Max Tools 30 Day Satisfaction Guarantee. See store policies for more details. Please call 800-629-3325 for any questions. We charge 8.75% sales tax for all orders shipping within California. Tax exemption is available if we are provided with a valid California resale certificate. For our full store policies please click here. Max Tools 30-Day Satisfaction Guarantee allows for the return of new and unused products in original factory condition and used defective products for 30 days from the date of purchase. Returns must be pre-approved by Max Tool and have a return merchandise authorization (RMA) number issued by Max Tool. Unauthorized returns will not be accepted. Return shipping costs are the responsibility of the buyer. We recommend using a shipping carrier with online tracking and insurance. Max Tool will replace the item with an identical item, issue a full store credit for the value of the item, or issue a refund for the value of the item, minus a 15% restocking fee. Original shipping and handling is non-refundable. For further details on our Return Policy Click Here Address: Max Tool 1669 Puddingstone Dr La Verne, CA 91750 Ph: (800) 629-3325 Fax: (800) 629-2329 Intl: +1 909 568 2800 Business Hours (US Pacific Time): Monday – Thursday: 6:00AM – 6:00PM Friday: 6:00 AM – 5:00 PM Viewing Now Makita A-93675 Micro-Polished 10″ 60T Miter Saw Blade

Technorati Tags: makita miter saw, miter saw

Click here to buy!

Toll Free: 1-877-987-2819 Jean-Claude Cayer Enterprises LTD. Pneumatic & Electric Tools – Outdoor Power Equipment Small Engines – Nails, Staples, Screws – Compressors Petits moteurs – Clous, agrafes, vis – Compresseurs Outils pneumatiques et électriques – Équipement de pelouse et jardin Shop by Category -Cordless Tools -Corded Tools -Framing Tools -Accessories -All -Air Guns -Miter Saws and Accessories -Hand Tools -Makita Lithium-Ion Tools -Air Compressors -Table Saws and Accessories -Other Milwaukee 2420-20 Hackzall™ M12™ Cordless Recip Saw- Bare Tool Condition: New MSRP*¹: $109.00 Photo Click Here for Manufacturer’s Warranty Features: -Only 11″ and 2.2 lbs. for cutting in tight spaces . -Keyless QUIK-LOK™ Blade Clamp allows for quick and easy blade changes. -All-Metal Gear Case for added durability. -Variable Speed Trigger for increased user control. -Battery Fuel Gauge displays remaining run-time. -Accepts both HACKZALL™ and SAWZALL® style blades . -Built-In LED Light illuminates work surface. -.. -Milwaukee Electric Tool Corporation introduces a new industry first – the HACKZALL™ M12™ Cordless Recip Saw, a compact, lightweight saw designed for powerful, versatile cutting in tight spaces for virtually all tradesman as they tackle plumbing, electrical, remodeling and HVAC applications. Featuring a 12V LITHIUM-ION battery, the HACKZALL™ cuts over 80 pieces of 1½” PVC on a single charge. The 2420 delivers a ½” stroke 3,000 times per minute for a smooth yet aggressive cut, and utilizes a keyless QUIK-LOK™ blade clamp to ensure quick and easy blade changes. The lightweight design offers less user fatigue as well as one-handed operation. Compact design makes it easier for users to access tight spaces or awkward angles. The HACKZALL™ features a variable speed trigger that provides increased user control and all-metal gear case and gears that live up to Milwaukee’s legendary durability. Additional features include a Built-in LED Light and Battery Fuel Gauge that displays the remaining run- time. Backed by Milwaukee’s 5-Year tool warranty and 2-Year battery warranty.. Specifications: Voltage12V Speed0-3000 SPM Stroke Length½” Blade ClampQUIK-LOK™ Universal ½” Tang TriggerVariable Speed BatteryLITHIUM-ION Tool Length11 in Tool Weight2.2 lbs Shippng Weight2.6 lbs Includes: -2420-20 Bare Tool. -(2) Hackzall™ Blades. Closer View/More Photos PLEASE NOTE INTERNATIONAL BUYERS, YOUR COUNTRY MIGHT CHARGE YOU DUTIES AND TAXES, THIS IS COMPLETELY OUT OF OUR CONTROL AND INCALCULABLE Jean Claude Cayer Enterprises LTD. Policies About Us We would like to take this opportunity to introduce ourselves. We are the leading and professional supplier of Electric and Pneumatic tools in the eastern Ontario region. We operate in the following channels: Industrial – Wholesale (Dealers) – Retail – Lumber Yards and Rental Outlets. We have been in business for 18 years. Yes we can write and speak in English and French fluently Payment Methods Information We only accept PayPal as a method of payment for purchases made on eBay. Contact Information Mailing Address: Jean-Claude Cayer Enterprises LTD. 708 Limoges Road Limoges, Ontario K0A 2M0 Canada Telephone: 1-613-443-2293 Toll Free Telephone: 1-877-987-2819 Fax: 1-613-443-2022 Business Hours: FROM MONDAY TO FRIDAY 7:00 AM to 5:00 PM(17:00) Eastern Standard Time Item’s Condition All our items are BRAND NEW unless declared otherwise. Normally if it is Reconditioned/Refurbished/Used it will be clearly writen in the title and/or in the description. Authorized Dealer and Service We are authorized Delaer and Service Center of all the brands we sell on eBay. We can cover all the warranties ourselves. BUY WITH CONFIDENCE Stock We normaly have everything we sell in Stock, we may sometimes run out stock due to selling here in the local store, at that time we order more of the item(s) in question and we will either offer a full refund or having a small waiting period! Sales Tax We must charge Federal and Provincial taxes. Ontario, New Brunswick and Newfoundland and Labrador Residents must pay 13% HSTNova Scotia Residents must pay 15% HST Quebec Residents must pay 5% GST and 8.5% TVQ/PST over the 5% GST. British Columbia Residents must pay 12% HST Manitoba, Prince Edward Island, Saskatchewan, Alberta, Northwest Territories, Yukon, Nunavut Residents must pay 5% GST. Shipping Information Shipping cost can be calculated by going to the “Shipping and payment” tab. Shipping Method Used All our item(s)/shipment(s)/package(s) are sent VIA UPS. Domestic(Canadian) shipments are shipped via UPS Standard(ground) unless asked otherwise by customer(extra charge), United States shipments are shipped vis UPS Standard(ground) unless asked otherwise by customer(extra charge), International(excluding United States) shipments are shipped via UPS Express Saver(air) unless asked otherwise by customer(extra charge). Delivery Waiting Time Canadian shipments should take between 1-7 Business days depending on your location in Canada. United States shipments should take between 3-8 business days depending on your location in United States and if it doesn’t get held in customs. International shipments should take between 2-8 business days depending on your location in the world and if it doesn’t get held in customs. BUY & PAY BEFORE 3:00PM EASTERN STANDARD TIME and we ship the same DAY! please note there is exceptions Tracking Number will be emailed and attached to your paypal payment Jean-Claude Cayer Enterprises is not responsible for any customs fees charged by your country, please contact us for more information. Thank you for understanding Local Pick-up and Prices We do not accept local pick-up. We do have the same prices in our local store has on eBay. eBay transactions/purchases can only be shipped. If you want to pick-up your item please contact us(see Contact Information tab). All prices are the same from eBay, our website and our local store, feel free to drop by and shop in the store with our experts sales representatives. Returns and Services If your are not satisfied with your purchase, you can return it at your cost for a refund. Refund is the total for the Product, original shipping will not be refunded. Taxes(if applied) and Total of the product will be refunded. We are authorized Service Center of all brands we sell on eBay and on our website, we will gladdly repair any tools that has been broken, free of charge if still under warranty, or with $60.00 CAD labour + parts if warranty as expired. For the lenght of the warranty from the manufacturer please refer to the “Manufacturer’s Warranty” tab just bellow the main picture/photo.. *¹ = Manufacturer’s suggested retail price Copyright © 2008-2012, JCCayer – 708 Limoges Road, P.O Box 280, Limoges, Ontario, K0A 2M0, Canada We will be closed from Friday December 23rd at 4:00PM until January 3rd at 7:00AM

Technorati Tags: makita miter saw, miter saw

Click here to buy!

Search Shop by Category Accessories Combo Kits Compressors & Generators Cordless Tools Drills/Drivers Hand Tools Heavy-Duty Home Measuring Tools Metalworking Nailers & Staplers Outdoor Products Sanders, Polishers, & Grinders Saws Specialty Tools Combo Kits Woodworking Workholding/ Toolholding Makita 12-in 100T Ultra-Fine Crosscutting Miter Saw Blade Model A-93734 List Price: $89.99 CPO Price: $49.99 You save: $40 (44%) Availability: In Stock Shipping: $6.99 Features Japanese ultra thin kerf carbide-tipped design provide smoother cuts with less drag on the motor and minimal material loss Full hardened and expertly hand-tensioned steel saw plates for true cuts Micro-grain carbide teeth are honed with up to 600 grit for a mirror finish SPECIFICATIONS Diameter 12-in Teeth 100 Hook Angle 5 Degrees Kerf Size 0.091-in Max. Speed 5,000 Type Ultra-fine crosscutting Application Hardwood Arbor Size 1-in Grind Style ATAF Plate Thickness 0.071-in INCLUDES 12-in 100T Ultra-Fine Crosscutting Miter Saw Blade – A-93734 WARRANTY 1-Year Makita For full warranty information, please contact us at 800-714-0969 Customer Satisfaction Guarantee CPO’s commitment to 100% customer satisfaction is backed by a 30-Day Money Back Guarantee! If you are unhappy with the condition of your product, send it back unused and we will replace it with a different one. If you changed your mind or are unhappy with your purchase, simply return it unused for a refund* *CPO’s 30-Day Money Back Guarantee is for the amount of the merchandise ordered and does not cover any additional expenses related to installation, materials, etc. CPO will cover the cost of return shipping in the event that an incorrect or defective item was sent. SHIPPING FAST SHIPPING! Most orders ship within 1 business day via FedEx Ground shipping! Some items (typically heavy items) ship within 2-3 business days and may ship via a different carrier. Shipment tracking information will be emailed to buyer after purchase. CPO Outlets will ONLY ship to BILLING addresses or CONFIRMED PayPal addresses. FOR SECURITY REASONS,CPO Outlets DOES NOT SHIP TO P.O BOXES. CPO Outlets only ships to the 48 contiguous United States. CPO Outlets will NOT process shipments to the following locations: AK, HI, Puerto Rico, APO/FPO, US Territory, Canadian and International Locations. PAYMENT CPO Outlets ONLY accepts payments via PayPal on our Ebay store. For security reasons, CPO does not accept payments from international accounts (even with a US address). State laws require that sales tax be charged on all orders shipped to addresses in California and Georgia. ABOUT CPO Established in 2003, CPO is a leading online retailer of home improvement products. CPO partners with top manufacturers and sells their products through independent brand-focused online stores. CPO online stores are known for their full selection of new products and an industry-leading selection of factory-reconditioned products, offering big savings without sacrificing performance. CPO serves professional and Do-It-Yourself customers who value quality, savings, super fast shipping, convenience, and top notch customer service. CPO customers return again and again for: Widest selection of products from trusted brands Big savings on factory reconditioned and clearance items (with full warranties) FAST SHIPPING! Most orders ship within 1 business day! Unrivaled customer service – Available 7 Days a Week Hassle free shopping experience CONTACT Call toll free: 800-714-0969 9:00AM-9:00PM EST Monday-Friday 9:00AM-6:00PM EST Saturday-Sunday Shop by Brand

Technorati Tags: makita miter saw, miter saw

Click here to buy!

Toll Free: 1-877-987-2819 Jean-Claude Cayer Enterprises LTD. Pneumatic & Electric Tools – Outdoor Power Equipment Small Engines – Nails, Staples, Screws – Compressors Petits moteurs – Clous, agrafes, vis – Compresseurs Outils pneumatiques et électriques – Équipement de pelouse et jardin Shop by Category -Cordless Tools -Corded Tools -Framing Tools -Accessories -All -Air Guns -Miter Saws and Accessories -Hand Tools -Makita Lithium-Ion Tools -Air Compressors -Table Saws and Accessories -Other Milwaukee 2445-20 M12™ Cordless High Performance Jig Saw – Bare Tool Condition: New MSRP*¹: $169.00 Photo Milwaukee Warranty. Features: Compact and Lightweight – Only 3.8 lbs and 8.75″ long Maximum Control – Innovative Hybrid Grip™ design delivers greater control by bringing the grip closer to the material with a variable speed trigger Powerful Cutting – 3/4″ Stroke length & 0-2,800 SPM for fast and controlled cutting through various materials Quick Changes – Quik-Lok™ T-Shank blade clamp and tool-free 450 bevel capability with positive lock at 900 Smooth Cutting – Designed to minimize vibration by keeping the weight over the cutting area LED Light and Fuel Gauge – Illuminates the cut line and displays remaining run-time Specifications: Voltage 12V Speed 0-2,800 SPM Stroke Length 3/4″ Trigger Variable Speed Bevel Capacity 45 Degree Bevel Adjust Tool-Free Lever Counterbalanced Mechanism Yes Tool Length 8 in. Tool Height 7 in. Tool Width 3 in. Net Tool Weight 3.8 lbs Shipping Weight 4.4 lbs Includes: M12™ Jig Saw Tool (1) Milwaukee® 10 TPI Wood Cutting T-Shank Jig Saw Blade (1) Anti-Splintering Insert (1) Non-Marring Shoe Closer View/More Photos PLEASE NOTE INTERNATIONAL BUYERS, YOUR COUNTRY MIGHT CHARGE YOU DUTIES AND TAXES, THIS IS COMPLETELY OUT OF OUR CONTROL AND INCALCULABLE Jean Claude Cayer Enterprises LTD. Policies About Us We would like to take this opportunity to introduce ourselves. We are the leading and professional supplier of Electric and Pneumatic tools in the eastern Ontario region. We operate in the following channels: Industrial – Wholesale (Dealers) – Retail – Lumber Yards and Rental Outlets. We have been in business for 18 years. Yes we can write and speak in English and French fluently Payment Methods Information We only accept PayPal as a method of payment for purchases made on eBay. Contact Information Mailing Address: Jean-Claude Cayer Enterprises LTD. 708 Limoges Road Limoges, Ontario K0A 2M0 Canada Telephone: 1-613-443-2293 Toll Free Telephone: 1-877-987-2819 Fax: 1-613-443-2022 Business Hours: FROM MONDAY TO FRIDAY 7:00 AM to 5:00 PM(17:00) Eastern Standard Time Item’s Condition All our items are BRAND NEW unless declared otherwise. Normally if it is Reconditioned/Refurbished/Used it will be clearly writen in the title and/or in the description. Authorized Dealer and Service We are authorized Delaer and Service Center of all the brands we sell on eBay. We can cover all the warranties ourselves. BUY WITH CONFIDENCE Stock We normaly have everything we sell in Stock, we may sometimes run out stock due to selling here in the local store, at that time we order more of the item(s) in question and we will either offer a full refund or having a small waiting period! Sales Tax We must charge Federal and Provincial taxes. Ontario, New Brunswick and Newfoundland and Labrador Residents must pay 13% HST Quebec Residents must pay 5% GST and 8.5% YVQ/PST over the 5% GST. British Columbia Residents must pay 12% HST Manitoba, Prince Edward Island, Saskatchewan, Alberta, Northwest Territories, Yukon, Nunavut Residents must pay 5% GST. Shipping Information Shipping cost can be calculated by going to the “Shipping and payment” tab. Shipping Method Used All our item(s)/shipment(s)/package(s) are sent VIA UPS. Domestic(Canadian) shipments are shipped via UPS Standard(ground) unless asked otherwise by customer(extra charge), United States shipments are shipped vis UPS Standard(ground) unless asked otherwise by customer(extra charge), International(excluding United States) shipments are shipped via UPS Express Saver(air) unless asked otherwise by customer(extra charge). Delivery Waiting Time Canadian shipments should take between 1-7 Business days depending on your location in Canada. United States shipments should take between 3-8 business days depending on your location in United States and if it doesn’t get held in customs. International shipments should take between 2-8 business days depending on your location in the world and if it doesn’t get held in customs. BUY & PAY BEFORE 3:00PM EASTERN STANDARD TIME and we ship the same DAY! please note there is exceptions Tracking Number will be emailed and attached to your paypal payment Jean-Claude Cayer Enterprises is not responsible for any customs fees charged by your country, please contact us for more information. Thank you for understanding Local Pick-up and Prices We do not accept local pick-up. We do have the same prices in our local store has on eBay. eBay transactions/purchases can only be shipped. If you want to pick-up your item please contact us(see Contact Information tab). All prices are the same from eBay, our website and our local store, feel free to drop by and shop in the store with our experts sales representatives. Returns and Services If your are not satisfied with your purchase, you can return it at your cost for a refund. Refund is the total for the Product, original shipping will not be refunded. Taxes(if applied) and Total of the product will be refunded. We are authorized Service Center of all brands we sell on eBay and on our website, we will gladdly repair any tools that has been broken, free of charge if still under warranty, or with $60.00 CAD labour + parts if warranty as expired. For the lenght of the warranty from the manufacturer please refer to the “Manufacturer’s Warranty” tab just bellow the main picture/photo.. *¹ = Manufacturer’s suggested retail price Copyright © 2008-2012, JCCayer – 708 Limoges Road, P.O Box 280, Limoges, Ontario, K0A 2M0, Canada We will be closed from Friday December 23rd at 4:00PM until January 3rd at 7:00AM

Technorati Tags: makita miter saw, miter saw